#21. Posted:
Rodent
  • Winter 2020
Status: Offline
Joined: Jan 21, 201212Year Member
Posts: 9,958
Reputation Power: 11642
Status: Offline
Joined: Jan 21, 201212Year Member
Posts: 9,958
Reputation Power: 11642
Bowd wrote
Rodent_Modz wrote
Bowd wrote New question - Anybody know why the matrix glitch chips blue light would just stay on and not flicker like it should.?

the console doesnt boot like this either.


wrong timing file or didn't load the timing file or bad chip


yeah so far ive only had luck with 2 chips the other 2 failed and now this one. might retry timing file and check over my solder

- might of been my pll point that was causing that. but definetly something wrong with these matrix chips i have bought . this ones not booting either


always post pics of your install so you can have others look it over easiest way to find an issue that your having or pics of jrunner when programming
and list timing files your using
#22. Posted:
Bowd
  • Junior Member
Status: Offline
Joined: Nov 19, 20185Year Member
Posts: 71
Reputation Power: 4
Status: Offline
Joined: Nov 19, 20185Year Member
Posts: 71
Reputation Power: 4
im now doing a 512mb jasper , and i have error 250 reading block 178 am i right in thinking this wont cause issues because it not being within the first 50 blocks. so when i write the xebuild image and new nand it will be fine?
#23. Posted:
The_OG_Modder
Status: Offline
Joined: Mar 28, 20204Year Member
Posts: 152
Reputation Power: 281
Status: Offline
Joined: Mar 28, 20204Year Member
Posts: 152
Reputation Power: 281
Bowd wrote im now doing a 512mb jasper , and i have error 250 reading block 178 am i right in thinking this wont cause issues because it not being within the first 50 blocks. so when i write the xebuild image and new nand it will be fine?


Jrunner should automatically remap bad blocks aslong as bands are the same maybe do an extra couple to be sure they are the same it should be fine and try fixing some points like post and or cpu rst
#24. Posted:
Rodent
  • Winter 2016
Status: Offline
Joined: Jan 21, 201212Year Member
Posts: 9,958
Reputation Power: 11642
Status: Offline
Joined: Jan 21, 201212Year Member
Posts: 9,958
Reputation Power: 11642
The_OG_Modder wrote
Bowd wrote im now doing a 512mb jasper , and i have error 250 reading block 178 am i right in thinking this wont cause issues because it not being within the first 50 blocks. so when i write the xebuild image and new nand it will be fine?


Jrunner should automatically remap bad blocks aslong as bands are the same maybe do an extra couple to be sure they are the same it should be fine and try fixing some points like post and or cpu rst


Correct
#25. Posted:
Bowd
  • Junior Member
Status: Offline
Joined: Nov 19, 20185Year Member
Posts: 71
Reputation Power: 4
Status: Offline
Joined: Nov 19, 20185Year Member
Posts: 71
Reputation Power: 4
So i got hold of some coolrunners.
whats the best timing file every else uses for these?
and is there anything you should solder on the chip for it to work, because i got another one , a jasper 512mb not booting xell.

i think i must be doing something wrong, i can upload photos of my soldering, but its really not needed, all the joints are solid in place and touching.

im using timing file 18 and 21 but no boot.

is it true i can try and boot it on slim setting and not phat, maybe that could help apart from that i have no ideas left. thought it could be my solder but there is no difference in the joints to how they look when i get a good one that boots.

update: i used kynar really thin wire for cpu rst not the wire that came with it . does that cause these issues?
it actually says to use shielded cable not sure what it means by that

the chips allso maybe not be genuine i bought them from ebay, and they didnt come in a cool runner box.

i allso read If your console is ,updated past dash 14699 then it is RGH 2
If you are pre 14699 then RGH 1
i didnt check the dash so dont know if thats my problem
#26. Posted:
The_OG_Modder
Status: Offline
Joined: Mar 28, 20204Year Member
Posts: 152
Reputation Power: 281
Status: Offline
Joined: Mar 28, 20204Year Member
Posts: 152
Reputation Power: 281
I pmd you bro I can help
Users browsing this topic: None
Jump to:


RECENT POSTS

HOT TOPICS