You are viewing our Forum Archives. To view or take place in current topics click here.
Problems updating Falcon jtag Bad blocks in nand
Posted:

Problems updating Falcon jtag Bad blocks in nandPosted:

Doink
  • Ladder Climber
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Hey TTG I'm having trouble updating the dash on my falcon Jtag.I first go on xex and open 360 Nand flasher and dump the Nand,wile its dumping it get three bad blocks one at 0x149,0x26D,and 0x3ff.So once I have the nand I open the latest xe-build, I than update the Nand to the latest dash and it say its good.So I would reboot and re-flash the updated nand back through Nand flasher,Reboot the console and get an e79 error or some type of 'E' error and get red flashing Lights not letting it boot up into the updated dash.When i first got it I sent it out to get fixed for the same problem and It came back updated and i don't know what was done to update it,also when I got it back I got a disc with nand on it.I have tried to update through j runner,tried remapping bad blocks and I still keep getting the E error and its not letting the console run.I also tried flashing through Xell and get the same problem.I am trying to avoid sending it out.If anyone can help it would be greatly appreciated!Thanks in advance!


Last edited by Doink ; edited 1 time in total
#2. Posted:
XeVon
  • TTG Master
Status: Offline
Joined: Jul 30, 201211Year Member
Posts: 851
Reputation Power: 44
Status: Offline
Joined: Jul 30, 201211Year Member
Posts: 851
Reputation Power: 44
try reflashing it with the nand on the disk then update it
#3. Posted:
TheWeekendModder
  • Prospect
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
#4. Posted:
Doink
  • Ladder Climber
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756
#5. Posted:
TheWeekendModder
  • Prospect
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
#6. Posted:
Doink
  • Ladder Climber
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
ok just did its on 16756 now
#7. Posted:
TheWeekendModder
  • Prospect
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
ok just did its on 16756 now


Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.
#8. Posted:
Doink
  • Ladder Climber
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
ok just did its on 16756 now


Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.
ok says there the same so how do i make a new nand from j runner is it by just updating it?
#9. Posted:
TheWeekendModder
  • Prospect
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Status: Offline
Joined: Apr 02, 201410Year Member
Posts: 651
Reputation Power: 38
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
ok just did its on 16756 now


Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.
ok says there the same so how do i make a new nand from j runner is it by just updating it?


Make sure the correct dash is selected in the upper right, as well as the correct mod type (jtag/rgh1/rgh2) then click the giant button that says "create xebuild image"...
#10. Posted:
Doink
  • Ladder Climber
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
Status: Offline
Joined: Jul 20, 201112Year Member
Posts: 354
Reputation Power: 19
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Doink wrote
TheWeekendModder wrote
Dental wrote try reflashing it with the nand on the disk then update it


Good point. OP: if you flash the nand provided on the disc can that (old) image get to dash?
im gittin the e79 when i use the nand on the disc.the only way to get it back to a dash is to use raw flash and flash it through xell and its the old nand dump so it goes back to 16756


flash that 16756 image back to the console and make sure that it is able to get to dash
ok just did its on 16756 now


Okay, so I would recommend grabbing a copy of your nand using 360 Nand Flasher (see my stickied post on kv flashing for info on this program). Dump your nand, then take that copy of the nand off to your PC, then dump the nand again.

Fire up Jrunner, and load the first dump as source1, and the 2nd dump as source2 and then hit "nand compare" to make sure they are the same and it will remap any bad blocks that exists.

Then build the new nand from Jrunner and flash that back to the console via Xell.
ok says there the same so how do i make a new nand from j runner is it by just updating it?


Make sure the correct dash is selected in the upper right, as well as the correct mod type (jtag/rgh1/rgh2) then click the giant button that says "create xebuild image"...
allright.do i put the dash that the nand is on which is 16756 or 16767 just wanna make sure
Jump to:
You are viewing our Forum Archives. To view or take place in current topics click here.