You are viewing our Forum Archives. To view or take place in current topics click here.
Hi Again Please help Jtagable Jasper E75
Posted:

Hi Again Please help Jtagable Jasper E75Posted:

TTG_Andrewwww
  • Resident Elite
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Hi today i received a joblot of xbox's and found this jasper 1st time i tried booting it and it loaded up to the xbox 360 logo (at this point i could tell it was a older dash it was quite dark compared to most recent dash)any way when it got to the logo it forze so i turned it off and tried again and it gave me E75 did a bit of googling and it says something about the network chi so while i was scanning over the board i saw this [ Register or Signin to view external links. ]

[ Register or Signin to view external links. ]

and i think this is what is causing it but i have no idea how to fix it sorry if the pic quality is bad after i saw that i thought screw it ill just put it to the side for now then i remembered i thought it was old dash so i solderd in my jr programmer and got 2 reads and sure enough it says patch 0 7363 and patch 1 7371 then i figured i will post on here and hope someone coukld help me Thanks in Advance
#2. Posted:
AplusConsoleRepair
  • Resident Elite
Status: Offline
Joined: Feb 09, 201311Year Member
Posts: 248
Reputation Power: 11
Status: Offline
Joined: Feb 09, 201311Year Member
Posts: 248
Reputation Power: 11
Those pads are definitely lifted, You would need an EXPERT pad repair tech and a replacement chip from a dead board for that job. Also, even if you successfully repair it you may run into another problem because I doubt someone would rip a chip from a working jasper, but then again you never know.
#3. Posted:
TTG_Andrewwww
  • Resident Elite
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
i dont know i bought a joblot of four consoles and i have this jasper then i also have a falcon that was in a the lot it has the same problem but on a much worses scale also 2 of the xbox's had the usb ports removed for some reason i dunno whos ever consoles they were truley did **** them
#4. Posted:
AplusConsoleRepair
  • Resident Elite
Status: Offline
Joined: Feb 09, 201311Year Member
Posts: 248
Reputation Power: 11
Status: Offline
Joined: Feb 09, 201311Year Member
Posts: 248
Reputation Power: 11
yea it's obvious he was using them as parts
#5. Posted:
TTG_Andrewwww
  • Resident Elite
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
unfortunatley yes sucks so bad but owel i only paid 6 pounds for a joblot of four consoles
#6. Posted:
5KMods
  • TTG Undisputed
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
That boards been mutilated.

Whoever tried swapping out Ethernet chip (ICS) ripped the majority of the pads, i wouldnt even bother with it unless i had a few hours free time to due trace fix and weld back new ICS.

Your better off using it for parts at this point, it would seriously be easier to take its cpu and transplant it to another jasper.
#7. Posted:
TTG_Andrewwww
  • Resident Elite
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Status: Offline
Joined: Mar 15, 201212Year Member
Posts: 214
Reputation Power: 8
Is that possible as i have a jadper with out a cpu so i gues i will see how.much it will cost to get it done
Jump to:
You are viewing our Forum Archives. To view or take place in current topics click here.