You are viewing our Forum Archives. To view or take place in current topics click here.
How to take apart an Xbox 360 Controller [TUT]
Posted:
How to take apart an Xbox 360 Controller [TUT]Posted:
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Hey thought i would make this just to show people how/what is needed to take apart a controller.
[size=25:5505c13704]Equipment needed:
Cellotape/Masking tape
Torx 8 screwdriver - it needs to be thin but also long otherwise it wont reach the screws
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 1:
Un-screw the screws which have been circled using your screwdriver
The orange circle will be found under a sticker just use a knife or a flat head screwdriver to peel this sticker off
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 2:
Get your cellotape and stick it on your buttons as shown in the picture below. When doing this apply some force so that the buttons stick to the cellotape.
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 3:
Push both thumbs on the joysticks whilst putting your fingers inbetween the crease of the controller (the gap where the front and back meet down the sides)
You should end up with the top shell off something like below. Yours shouldnt have the wires like mine does because mines modded
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 4:
Now take the thumb sticks off, the top plastic covering (where sync button is) and the bottom (where mic slot is)
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 5:
I would advise taking both the rumble packs off this can be done my simply pulling them out like you would a plug. This way they dont get in the way .
[size=25:5505c13704]Step 6:
To remove the circuit board (the big green thing) push the left and right trigger in at the same time and slowly pull the circuit board out MAKE SURE YOU DONT DAMAGE THE SILVER PRONGS THAT ATTACH TO THE BATTERY SO GO SLOWLY!
I hope this helped if so +Rep maybe
Sorry if this is in wrong section.
Last edited by JamJar ; edited 1 time in total
[size=25:5505c13704]Equipment needed:
Cellotape/Masking tape
Torx 8 screwdriver - it needs to be thin but also long otherwise it wont reach the screws
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 1:
Un-screw the screws which have been circled using your screwdriver
The orange circle will be found under a sticker just use a knife or a flat head screwdriver to peel this sticker off
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 2:
Get your cellotape and stick it on your buttons as shown in the picture below. When doing this apply some force so that the buttons stick to the cellotape.
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 3:
Push both thumbs on the joysticks whilst putting your fingers inbetween the crease of the controller (the gap where the front and back meet down the sides)
You should end up with the top shell off something like below. Yours shouldnt have the wires like mine does because mines modded
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 4:
Now take the thumb sticks off, the top plastic covering (where sync button is) and the bottom (where mic slot is)
[ Register or Signin to view external links. ]
[size=25:5505c13704]Step 5:
I would advise taking both the rumble packs off this can be done my simply pulling them out like you would a plug. This way they dont get in the way .
[size=25:5505c13704]Step 6:
To remove the circuit board (the big green thing) push the left and right trigger in at the same time and slowly pull the circuit board out MAKE SURE YOU DONT DAMAGE THE SILVER PRONGS THAT ATTACH TO THE BATTERY SO GO SLOWLY!
I hope this helped if so +Rep maybe
Sorry if this is in wrong section.
Last edited by JamJar ; edited 1 time in total
#2. Posted:
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Bump bbn)
- 0useful
- 0not useful
#3. Posted:
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Bump bbn)
- 0useful
- 0not useful
#4. Posted:
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Bump just incase people need to know
- 0useful
- 0not useful
#5. Posted:
Status: Offline
Joined: Jan 20, 201014Year Member
Posts: 8,013
Reputation Power: 2165
Status: Offline
Joined: Jan 20, 201014Year Member
Posts: 8,013
Reputation Power: 2165
Try not to bump your topic so much eh ;)
Good post though.
+Rep'd.
bbn)
Good post though.
+Rep'd.
bbn)
- 0useful
- 0not useful
#6. Posted:
Status: Offline
Joined: Jun 18, 200914Year Member
Posts: 3,907
Reputation Power: 342
Status: Offline
Joined: Jun 18, 200914Year Member
Posts: 3,907
Reputation Power: 342
This is the second time you have posted this, I commented on the last one.
Ill get link
EDIT:
Link
Forums/viewtopic/t=132588.html
Ill get link
EDIT:
Link
Forums/viewtopic/t=132588.html
- 0useful
- 0not useful
#7. Posted:
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
Status: Offline
Joined: Apr 27, 201014Year Member
Posts: 336
Reputation Power: 18
skatertg wrote Try not to bump your topic so much eh ;)
Good post though.
+Rep'd.
bbn)
Lol Sorry i just dont want it getting Lost amongst all the threads because you never know when someone may need this
- 0useful
- 0not useful
You are viewing our Forum Archives. To view or take place in current topics click here.