You are viewing our Forum Archives. To view or take place in current topics click here.
Falcon JTAG Issues
Posted:
Falcon JTAG IssuesPosted:
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Hello,
I've been trying to do my first JTAG Hack on a Falcon, and I've burned DB1F1 and the point below, I plan on doing the AUD_Clamp wiring method now. As people seem to say it is much more stable, and is suppose to be better wiring. I saw on a tutioral for this, that you need the jumper wires if your not using the JTAG QSBs, when they say "jumper wires" does that basically mean the same as briding 2 points with a wire? I just need to know this because I would rather do direct wiring than QSBs.
Any help would be greatly appreciated Thanks for reading. ;)
I've been trying to do my first JTAG Hack on a Falcon, and I've burned DB1F1 and the point below, I plan on doing the AUD_Clamp wiring method now. As people seem to say it is much more stable, and is suppose to be better wiring. I saw on a tutioral for this, that you need the jumper wires if your not using the JTAG QSBs, when they say "jumper wires" does that basically mean the same as briding 2 points with a wire? I just need to know this because I would rather do direct wiring than QSBs.
Any help would be greatly appreciated Thanks for reading. ;)
#2. Posted:
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
yes you need to install the jumper wire otherwise you will get e79.
aud_clamp uses alt db1f1 point aswell and is more stable
aud_clamp uses alt db1f1 point aswell and is more stable
- 0useful
- 0not useful
#3. Posted:
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
-Mafia5K- wrote yes you need to install the jumper wire otherwise you will get e79.
aud_clamp uses alt db1f1 point aswell and is more stable
When you saying jumper wire, does that mean I use kynar wire and bridge the 2 points?
- 0useful
- 0not useful
#4. Posted:
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Capital-H wrote-Mafia5K- wrote yes you need to install the jumper wire otherwise you will get e79.
aud_clamp uses alt db1f1 point aswell and is more stable
When you saying jumper wire, does that mean I use kynar wire and bridge the 2 points?
yes pins 4 & 7 on J2D2
- 0useful
- 0not useful
#5. Posted:
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
-Mafia5K- wroteCapital-H wrote-Mafia5K- wrote yes you need to install the jumper wire otherwise you will get e79.
aud_clamp uses alt db1f1 point aswell and is more stable
When you saying jumper wire, does that mean I use kynar wire and bridge the 2 points?
yes pins 4 & 7 on J2D2
Can I also use the long yellow and red wire, cut them and solder them directly? Thanks for the help ;)
EDIT: Its basically the same process except instead of soldering to ROL, and DB1F1, you soldering to the bottom leg of Q2N1, and solder the other wire to the DVD Linker wire? Is this correct?
- 0useful
- 0not useful
#6. Posted:
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Capital-H wrote-Mafia5K- wroteCapital-H wrote-Mafia5K- wrote yes you need to install the jumper wire otherwise you will get e79.
aud_clamp uses alt db1f1 point aswell and is more stable
When you saying jumper wire, does that mean I use kynar wire and bridge the 2 points?
yes pins 4 & 7 on J2D2
Can I also use the long yellow and red wire, cut them and solder them directly? Thanks for the help ;)
i dont know what you mean by that, but yes you need wire and 1n1418? switching diodes black line facing away from J2D2. DONT QOUTE THE MODEL OF DIODE I POSTED I AM NOT 100% SURE.
- 0useful
- 0not useful
#7. Posted:
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Thanks, yeah I think I know the one your talking about I bought like x100 of them, What I think I'm going to do is cut the wire from the QSBS use the alternative point underneath the board, and splice the DVD Linker wire, and solder it to that, I'll follow a tutioral and hope all goes well
- 0useful
- 0not useful
#8. Posted:
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Capital-H wrote Thanks, yeah I think I know the one your talking about I bought like x100 of them, What I think I'm going to do is cut the wire from the QSBS use the alternative point underneath the board, and splice the DVD Linker wire, and solder it to that, I'll follow a tutioral and hope all goes well
Your refering to AUD_CLAMP + OPEN TRAY, I thought you said you wanted AUD_Clamp If i had to choose i would stay away from OPEN TRAY its the worst out of them all.
Aud clamp wiring is
Jumper from PIN4 - 7
J2D2 PIN1 to ALT DB1F1
J2D2 PIN 2 to Q2N1 Aud Clamp point
Picture:
- 0useful
- 0not useful
#9. Posted:
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
Status: Offline
Joined: Jan 10, 201113Year Member
Posts: 147
Reputation Power: 5
-Mafia5K- wroteCapital-H wrote Thanks, yeah I think I know the one your talking about I bought like x100 of them, What I think I'm going to do is cut the wire from the QSBS use the alternative point underneath the board, and splice the DVD Linker wire, and solder it to that, I'll follow a tutioral and hope all goes well
Your refering to AUD_CLAMP + OPEN TRAY, I thought you said you wanted AUD_Clamp If i had to choose i would stay away from OPEN TRAY its the worst out of them all.
Aud clamp wiring is
Jumper from PIN4 - 7
J2D2 PIN1 to ALT DB1F1
J2D2 PIN 2 to Q2N1 Aud Clamp point
Picture:
I don't understand J2D2 PIN1 to ALT DB1F1, what is the alternative DB1F1? I burnt DB1F1, and the point below it
EDIT: I understand thanks for your help
Last edited by InsideModzUK ; edited 1 time in total
- 0useful
- 0not useful
#10. Posted:
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Status: Offline
Joined: Jun 19, 201013Year Member
Posts: 5,070
Reputation Power: 216
Capital-H wrote-Mafia5K- wroteCapital-H wrote Thanks, yeah I think I know the one your talking about I bought like x100 of them, What I think I'm going to do is cut the wire from the QSBS use the alternative point underneath the board, and splice the DVD Linker wire, and solder it to that, I'll follow a tutioral and hope all goes well
Your refering to AUD_CLAMP + OPEN TRAY, I thought you said you wanted AUD_Clamp If i had to choose i would stay away from OPEN TRAY its the worst out of them all.
Aud clamp wiring is
Jumper from PIN4 - 7
J2D2 PIN1 to ALT DB1F1
J2D2 PIN 2 to Q2N1 Aud Clamp point
Picture:
I don't understand J2D2 PIN1 to ALT DB1F1, what is the alternative DB1F1? I burnt DB1F1, and the point below it
[ Register or Signin to view external links. ]
- 0useful
- 0not useful
You are viewing our Forum Archives. To view or take place in current topics click here.