You are viewing our Forum Archives. To view or take place in current topics click here.
Xbox 360 Rapidfire
Posted:
Xbox 360 RapidfirePosted:
Status: Offline
Joined: Apr 14, 201014Year Member
Posts: 3,051
Reputation Power: 191
Status: Offline
Joined: Apr 14, 201014Year Member
Posts: 3,051
Reputation Power: 191
Edit: Stickied by TTG Zac - Very Good post mate!
Works for Halo 3 , MW2, COD5, More...
Rapidfire With "12f683"
Stage 1: Building the Programmer
ok first we will get warmed you by building the programmer...
Equipment required....
(May or may not need some stuff depends on install and controller)
-Soldering iron 15-30W
-Solder
-30AWG wire (Thin Wire)
-Pic12f683
-N-channel MOSfet (Bs170 or IRF 510)
-Momentary Switch
-1N4148 Diode
-Resistor 330 Ohm
-Resistor 470 Ohm
-Resistor 10K
-Resistor 1K
-Resistor 22K
-Resistor 2.2k
-Leds 3-5MM (Optional)
-Socket 8 pin for the chip (recommended but optional)
-RS232 (serial) female socket.
-USB Cable For Power(Any 5V Source)
OK that said here is the schematic for the programmer pretty straight Forward...Depending if you are going to use leds, I did...it tells you power and read/write...
[ Register or Signin to view external links. ]
Top uses Bs170 & Bottom IRF 510 both will work just different wiring
[ Register or Signin to view external links. ]
Step 2: Programming
Decide on the style of Rapid fire you want either
Sleeper:
No cutting or drilling required the controller looks totally stock has 3 mode..
Mode1= Halo 3 Dual Trigger
Mode2= Cod 5 WAW
Mode3= MW2
Rapidfire RF:
You have to install 2 buttons one for each trigger (only to change mode you will not actually use it to fire) .This one has the ability to enable/disable Rapidfire on each trigger independently...you can also have different mode in both triggers at once, e.g.
Left Trigger Halo3 speed, Right trigger Cod4 speed,
Left trigger Cod5 speed right trigger halo3 Speed, so on and so on...
Mode1= Halo 3 Dual Trigger
Mode2= Cod 5 WAW
Mode3= MW2
Mode4= Cod 4 Ultrafast
Once you have chosen:
1.Install WinPic800.exe
2.Open Win PIC make sure your programmer in connected...
you might have to choose English from the second last menu item at the top...
go to
Settings>Hardware>Choose JDM Programmer and Select your com port and select APPLY...Test hardware by pressing (Ctrl+T)
Now You are ready for programming...Make sure you have Pic12F683 selected at the top right hand corner.
Open the Hex File (File>Open), (either GameplayRF.hex or Sleeper.hex) depending on the style you are going to be modding it...
Then simply got to
Device>Program All (Ctrl+P)
DONE now you are ready to put it in your Controller
Step 3: Installation
1. Decide which controller you have & wire according to how you programmed your chip!!!
[ Register or Signin to view external links. ]
Use Resistor Colours.exe to know what each resistor looks like for the install!!!
Sleeper Install
OK if you have decided to do the Sleeper install here is how you wire the Controller.
CG Sleeper
[ Register or Signin to view external links. ]
Matrix Sleeper
[ Register or Signin to view external links. ]
Rapidfire RF install
OK if you have decided to do the Rapidfire RF install here is how you wire the Controller.
CG Rapidfire RF
[ Register or Signin to view external links. ]
Matrix Rapidfire RF
[ Register or Signin to view external links. ]
Installed Pictures
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
Last edited by -Avery- ; edited 2 times in total
Rapid Fire Tutorial for xbox 360
Works for Halo 3 , MW2, COD5, More...
Rapidfire With "12f683"
Stage 1: Building the Programmer
ok first we will get warmed you by building the programmer...
Equipment required....
(May or may not need some stuff depends on install and controller)
-Soldering iron 15-30W
-Solder
-30AWG wire (Thin Wire)
-Pic12f683
-N-channel MOSfet (Bs170 or IRF 510)
-Momentary Switch
-1N4148 Diode
-Resistor 330 Ohm
-Resistor 470 Ohm
-Resistor 10K
-Resistor 1K
-Resistor 22K
-Resistor 2.2k
-Leds 3-5MM (Optional)
-Socket 8 pin for the chip (recommended but optional)
-RS232 (serial) female socket.
-USB Cable For Power(Any 5V Source)
OK that said here is the schematic for the programmer pretty straight Forward...Depending if you are going to use leds, I did...it tells you power and read/write...
[ Register or Signin to view external links. ]
Top uses Bs170 & Bottom IRF 510 both will work just different wiring
[ Register or Signin to view external links. ]
Step 2: Programming
Decide on the style of Rapid fire you want either
Sleeper:
No cutting or drilling required the controller looks totally stock has 3 mode..
Mode1= Halo 3 Dual Trigger
Mode2= Cod 5 WAW
Mode3= MW2
Rapidfire RF:
You have to install 2 buttons one for each trigger (only to change mode you will not actually use it to fire) .This one has the ability to enable/disable Rapidfire on each trigger independently...you can also have different mode in both triggers at once, e.g.
Left Trigger Halo3 speed, Right trigger Cod4 speed,
Left trigger Cod5 speed right trigger halo3 Speed, so on and so on...
Mode1= Halo 3 Dual Trigger
Mode2= Cod 5 WAW
Mode3= MW2
Mode4= Cod 4 Ultrafast
Once you have chosen:
1.Install WinPic800.exe
2.Open Win PIC make sure your programmer in connected...
you might have to choose English from the second last menu item at the top...
go to
Settings>Hardware>Choose JDM Programmer and Select your com port and select APPLY...Test hardware by pressing (Ctrl+T)
Now You are ready for programming...Make sure you have Pic12F683 selected at the top right hand corner.
Open the Hex File (File>Open), (either GameplayRF.hex or Sleeper.hex) depending on the style you are going to be modding it...
Then simply got to
Device>Program All (Ctrl+P)
DONE now you are ready to put it in your Controller
Step 3: Installation
1. Decide which controller you have & wire according to how you programmed your chip!!!
[ Register or Signin to view external links. ]
Use Resistor Colours.exe to know what each resistor looks like for the install!!!
Sleeper Install
OK if you have decided to do the Sleeper install here is how you wire the Controller.
CG Sleeper
[ Register or Signin to view external links. ]
Matrix Sleeper
[ Register or Signin to view external links. ]
Rapidfire RF install
OK if you have decided to do the Rapidfire RF install here is how you wire the Controller.
CG Rapidfire RF
[ Register or Signin to view external links. ]
Matrix Rapidfire RF
[ Register or Signin to view external links. ]
Installed Pictures
[ Register or Signin to view external links. ]
[ Register or Signin to view external links. ]
http://www.megaupload.com/?d=NH4KC0N9 Last edited by -Avery- ; edited 2 times in total
The following 31 users thanked -Avery- for this useful post:
Mr_Robot (02-26-2017), TTG_Troll_ (02-09-2015), Kaspur (04-26-2014), XeRed (04-23-2014), Blzd (03-19-2014), Da_FBi (12-05-2012), Jesus1217 (11-12-2012), ModdingForYa (11-02-2012), DynamicBomb (06-28-2012), Foostest (06-25-2012), Insigma (04-25-2012), Build (02-18-2012), jakerose234 (01-03-2012), Tobacco (11-05-2011), SovietRussia (07-12-2011), EMB (05-26-2011), TTG_W33DzZ (03-30-2011), clawxdelvecchio (03-29-2011), TTG_Tman (03-20-2011), TTGxPerfXtionZx (03-14-2011), R3cKL3SS_oX (03-09-2011), Aznboy38 (01-02-2011), xSonic_Fanboy (12-30-2010), LuFc-Ashley (12-30-2010), -Recklesss- (09-23-2010), GasaiYuno (07-14-2010), Eliteee (07-14-2010), Buncez (07-02-2010), BoXMan (06-05-2010), Brasko (05-30-2010), 0141 (05-25-2010)
#2. Posted:
Status: Offline
Joined: Apr 23, 201014Year Member
Posts: 640
Reputation Power: 25
Status: Offline
Joined: Apr 23, 201014Year Member
Posts: 640
Reputation Power: 25
Great Great tut [= Ill try on a old controller 8)
- 1useful
- 1not useful
#3. Posted:
Status: Offline
Joined: Jan 15, 201014Year Member
Posts: 2,438
Reputation Power: 113
nice tut hunt your tuts just keep getting better and better
- 0useful
- 0not useful
#4. Posted:
Status: Offline
Joined: Apr 14, 201014Year Member
Posts: 3,051
Reputation Power: 191
Status: Offline
Joined: Apr 14, 201014Year Member
Posts: 3,051
Reputation Power: 191
iElectrox1 wrote Great Great tut [= Ill try on a old controller 8)
Sounds good but be careful. It harder to do this than it is to jtag. lol trust me.
- 1useful
- 1not useful
#5. Posted:
Status: Offline
Joined: Jun 18, 200914Year Member
Posts: 3,907
Reputation Power: 342
Status: Offline
Joined: Jun 18, 200914Year Member
Posts: 3,907
Reputation Power: 342
TTG_Hunt wrote
Sounds good but be careful. It harder to do this than it is to jtag. lol trust me.
Yeah, soldering on those controllers inst easy, everything is so small!!!
- 0useful
- 0not useful
#6. Posted:
Status: Offline
Joined: May 16, 201013Year Member
Posts: 54
Reputation Power: 27
Status: Offline
Joined: May 16, 201013Year Member
Posts: 54
Reputation Power: 27
I tried this on an old controller and its works only for MW2 but not for other games . But still, im okay with that. Very nice tutorial man. It was very helpful.
- 0useful
- 0not useful
#7. Posted:
Status: Offline
Joined: Feb 03, 201014Year Member
Posts: 8,036
Reputation Power: 1128
Status: Offline
Joined: Feb 03, 201014Year Member
Posts: 8,036
Reputation Power: 1128
Nice post man, mods are the way forward 8)
+Rep inbound.
+Rep inbound.
- 1useful
- 0not useful
#8. Posted:
Status: Offline
Joined: Mar 19, 201014Year Member
Posts: 855
Reputation Power: 166
Status: Offline
Joined: Mar 19, 201014Year Member
Posts: 855
Reputation Power: 166
Jesus man this post is amazing. I love you Kracker. You make the best post's. Did this take like 5 hours? I remember when we where chillen in a party and you were working on this post. Anyway ahhmzing post! Would say Bump but no need since Zac stickied.
Tylan
Tylan
- 0useful
- 0not useful
#9. Posted:
Status: Offline
Joined: Apr 30, 200915Year Member
Posts: 773
Reputation Power: 79
Status: Offline
Joined: Apr 30, 200915Year Member
Posts: 773
Reputation Power: 79
damn the wires are tiny, but im going to finish tomoorw, will report back(:
- 0useful
- 0not useful
#10. Posted:
Status: Offline
Joined: Apr 13, 201014Year Member
Posts: 1,836
Reputation Power: 265
Status: Offline
Joined: Apr 13, 201014Year Member
Posts: 1,836
Reputation Power: 265
Great tut man easy to follow as well!
- 0useful
- 0not useful
You are viewing our Forum Archives. To view or take place in current topics click here.