5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

Can I join the argument or no??

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220. (I've repaired thousands of consoles never seen this error once).

As ive already said he was wrong and the erro is 0022. (OP mis-Read Code)

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0022 on them has nothing to do with the GPU.


This converstaion is done and your argument is also done.

OP, take everyones suggestion as it is and base it on facts.. more importantly if you make a thread asking for this support supply neccesery info or you get crappy responces (proven by this thread).
Godspeed.

DrinkCoke wrote [snip]

Can I join the argument or no??

It's probably not in your best interest; 5k knows all about JTAG's/RGH's considering he owns one of the top shops here on TTG.
-real

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220.

As ive already said he was wrong and the erro is 0022.

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0202 on them has nothing to do with the GPU.


This converstaion is done and your argument is pointless.

Godspeed.

How do you know the error was 0022 and not 0220 with out him providing proof? I told him a way to fix 0220 before you even came to this topic. Also, "nobody ever said it Cannot be the GPU." Look at your previous post "This has nothing to do with gpu or cpu, stop posting garbage." Do you not remember what you posted?

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220.

As ive already said he was wrong and the erro is 0022.

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0202 on them has nothing to do with the GPU.


This converstaion is done and your argument is pointless.

Godspeed.

How do you know the error was 0022 and not 0220 with out him providing proof? I told him a way to fix 0220 before you even came to this topic. Also, "nobody ever said it Cannot be the GPU." Look at your previous post "This has nothing to do with gpu or cpu, stop posting garbage." Do you not remember what you posted?

Maybe becuase your pushing the OP, to get his console reballed without even confirming the code (really how many people have even seen 0220 its so uncommon it should be non-existant).

The fact that i had to come here and tell him to recheck was pathetic, at this point the only way of knowing is to write the orignal nand back to the system. - Which for some reason you and a few others have a hard time asking him too do and rather suggest to reflow/reball it.

It's one thing if you do this to your consoles you get for repair, but dont come to provide support and provide sub-par info.


reflow/reball should be last resort in the situation after exhausting/confirming its nothing else.
Example : He gets it reballed has same issue becuase its simply wiring or a corrupt nand - explain to me why this is useful?

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220.

As ive already said he was wrong and the erro is 0022.

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0202 on them has nothing to do with the GPU.


This converstaion is done and your argument is pointless.

Godspeed.

How do you know the error was 0022 and not 0220 with out him providing proof? I told him a way to fix 0220 before you even came to this topic. Also, "nobody ever said it Cannot be the GPU." Look at your previous post "This has nothing to do with gpu or cpu, stop posting garbage." Do you not remember what you posted?

Maybe becuase your pushing the OP, to get his console reballed without even confirming the code (really how many people have even seen 0220 its so uncommon it should be non-existant).

The fact that i had to come here and tell him to recheck was pathetic, at this point the only way of knowing is to write the orignal nand back to the system. - Which for some reason you and a few others have a hard time asking him too do and rather suggest to reflow/reball it.

Have you been following the thread? If not look at my first 2 posts. Tell me, was I pushing him to get it reballed? Then you joined the conversation saying it CANNOT be 0220, which then I replied I HAVE seen and fixed the error code 0220.

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220.

As ive already said he was wrong and the erro is 0022.

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0202 on them has nothing to do with the GPU.


This converstaion is done and your argument is pointless.

Godspeed.

How do you know the error was 0022 and not 0220 with out him providing proof? I told him a way to fix 0220 before you even came to this topic. Also, "nobody ever said it Cannot be the GPU." Look at your previous post "This has nothing to do with gpu or cpu, stop posting garbage." Do you not remember what you posted?

Maybe becuase your pushing the OP, to get his console reballed without even confirming the code (really how many people have even seen 0220 its so uncommon it should be non-existant).

The fact that i had to come here and tell him to recheck was pathetic, at this point the only way of knowing is to write the orignal nand back to the system. - Which for some reason you and a few others have a hard time asking him too do and rather suggest to reflow/reball it.

Have you been following the thread? If not look at my first 2 posts. Tell me, was I pushing him to get it reballed? Then you joined the conversation saying it CANNOT be 0220, which then I replied I HAVE seen and fixed the error code 0220.

Your joking right this is starting to make you seem slightly dilusional - I wasnt talking to you until you replied saying its not the nand or wiring and to reball it... you tried contradicting me when we both know im most likely right and made yourself look arragent as hell.

If you have seen and fixed 0220 with reball (i doubt it), it doesnt matter becuase thats not OP's error code.

Nothing more needs to be discussed until OP is willing to write the orignal nand back.

Anything else you want to argue about today?

ok im sorry i started this in a way buy giving 0022 error code fix. but what you should do is flash back the original nand and take the jtag wiring off and see what it does if the console boots ok then put the jtag wiring back on and then flash a new image or just do the jtag process all over again.

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid.

Im talking about the 0220 error, which does exist. Also, the error 0022 is the GPU, I have seen countless topics about how people fixed that error by reball/reflowing. When running a legitimate repair business, its always good practice to do the best you can in the repair. Reballing does not cost much more than reflowing.

OP, does not have 0220.

As ive already said he was wrong and the erro is 0022.

Have you read the thread at all? Your argument is invalidnobody ever said it Cannot be the GPU. Simply said you should not be suggesting it is until you know it is.

I dont care if 99% of retails with 0022 is gpu. This is a Jtag and 99% of the time 0202 on them has nothing to do with the GPU.


This converstaion is done and your argument is pointless.

Godspeed.

How do you know the error was 0022 and not 0220 with out him providing proof? I told him a way to fix 0220 before you even came to this topic. Also, "nobody ever said it Cannot be the GPU." Look at your previous post "This has nothing to do with gpu or cpu, stop posting garbage." Do you not remember what you posted?

Maybe becuase your pushing the OP, to get his console reballed without even confirming the code (really how many people have even seen 0220 its so uncommon it should be non-existant).

The fact that i had to come here and tell him to recheck was pathetic, at this point the only way of knowing is to write the orignal nand back to the system. - Which for some reason you and a few others have a hard time asking him too do and rather suggest to reflow/reball it.

Have you been following the thread? If not look at my first 2 posts. Tell me, was I pushing him to get it reballed? Then you joined the conversation saying it CANNOT be 0220, which then I replied I HAVE seen and fixed the error code 0220.

Your joking right this is starting to make you seem slightly dilusional - I wasnt talking to you until you replied saying its not the nand or wiring and to reball it... you tried contradicting me when we both know im most likely right and made yourself look arragent as hell.

If you have seen and fixed 0220 with reball (i doubt it), it doesnt matter becuase thats not OP's error code.

Nothing more needs to be discussed until OP is willing to write the orignal nand back.

Anything else you want to argue about today?

You were talking to me. Look back to your first post. "of course your going to get dumba*s Responces." Responses is plural, meaning, more than one. There were only two people that commented before you posted. Me and CustomeRGH. If you weren't talking to me, then you should probably choose your words more carefully.

I was given a specific error code(0220). Therefore, I gave a way to fix said error code(0220). If I was given the wrong error code(0220) from the beginning and it turns out to be another error code(0022), then its not my fault for giving the fix to 0220.

If you dont want to take my word for it heres some people that fixed or have been saying to fix 0220 with a reball:

Look at ICY-TANK's posts [ Register or Signin to view external links. ]
Look at Texasboneking: [ Register or Signin to view external links. ]

@customeRGH You don't need to apologize to anyone. You were right about how to fix 0022. Its just that some people, when they get a badge, they think they know everything and when they mess up a bit, they try to attack everyone who points out their flaws. Unfortunately for that person, he ran into someone who HAS fixed that error code before.

When a GPUs (in this example) solder balls have crystallized and some have broke and lost its connection, you get the RROD. Error code 0220 happens when over time the X-clamps have lost some of its tension causing heat to build up in some areas of the chip. After a period of heating up and then cooling down, the area where the heatsink was loose has been damaged and the solder balls underneath have broken and some points have lost connection. This is were the X-clamp fix (or reballing/reflowing) comes in play. The x-clamps fix, if tensioned correctly, can fix it by using the box's heat to heat up the solder balls underneath and regaining some connection. A reball is preferred because it completely replaces the damaged solder balls, as opposed to the X-clamp fix or a reflow.

A bad flash would be an error E79 or 0110. If I'm not mistaken.