I already said my code was 0220 and I will post pics soon

I will check again sir and tell u

[ Register or Signin to view external links. ] This is the photo link

The error code is actually 0022

[ Register or Signin to view external links. ]

Paulyd972738 wrote Ok I will try reflow but I don't know why it doesn't even boot into xell?

When a JTAG gets rrod, it won't work at all pretty much

1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

661King wrote

5KMods wrote

CustomRGH wrote 1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).

This has nothing to do with gpu or cpu, stop posting garbage.

You have a RGH/JTAG board and have either flashed a corrupted image or your wiring is a mess plain and simple.

Either post pics or get help elsewhere this is just a thread packed with stupid suggestions/Spam based on OP's. lack on info.


Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.

It has nothing to do with flashing the Nand. It is a hardware failure. As Ive stated before, I have fixed consoles with such an error. A reball of the GPU/CPU should be able to fix it.

You dont understand the error, you wont be in business long if you reball every 0022 you get, thats just stupid. Already mentioned this thread is full of BS suggestions and at this point,there are no clear answers. What makes you think it needs to be reballed from what OP has told us?




Write your orignal nand back to confirm its working.
Before testing ...Make sure if its a RGH to turn the CR Switch to PRG before testing, or if its a Jtag remove your wiring.