Xbox 360How to update your RGH to Dashboard 17559 [Step 4 Step] EASY
Posted:

Xbox 360How to update your RGH to Dashboard 17559 [Step 4 Step] EASYPosted:

Streamah
  • Summer 2020
Status: Offline
Joined: May 24, 201013Year Member
Posts: 10,103
Reputation Power: 3697
Status: Offline
Joined: May 24, 201013Year Member
Posts: 10,103
Reputation Power: 3697
How to properly update your RGH to 17544

thing you will need

a rgh console on a later dashboard

xebuild updated for 17559
17526 XeBuild Download Link

Dashlaunch 3.21
Dashlaunch 3.20Download

Flash 360
Flash 360 Download

If you have a corona motherboard, use simple nand flasher

your CPU KEY from XELL and a USB drive


Step 1 - Flash 360

Download Flash 360 and install the whole Flash 360 folder to a USB


Next, turn your rgh on and go into xex menu then plug in your usb

When xex menu loads up press rb to navigate to the usb storage device

Click Flash360 folder , then run flash360.xex. When Flash360 loads up you will be asked to

Button X = Backup current Nand to File <----------------- press X

Then on next prompt screen

Button A = Save entire nand to file <--------------- press A

It will take a moment to save your current nand to file as flashdmp.bin, once complete press any button then press BACK button to return to main menu

Remove USB from RGH and plug in to PC then open the flash 360 folder and find your flashdmp.bin


Step 2 - XeBuild 17544

Download and unzip XeBuild 17544 and run the xebuild application


Drag and drop your flashdmp.bin into the source file and enter your CPUKey in the CPUKey slot



then click Generate hacked image

image built!



Press Yes to close the program

Your new 17559 nand (updflash.bin) is now inside the Flash360 folder on the USB drive

Save your old flashdmp.bin somewhere safe then remove it from the flash360 folder.

This is how your flash360 folder should look before you plug your USB back into RGH



Step 3 - Flash 360 new nand
Now plug USB back into RGH and run Flash 360 again

Once Flash 360 is loaded press

Button A = Write updflash.bin to Nand <----------- press A

next, Press

Button A = Raw Flash with keeping current kv/config <--------- press A

Next Press START to continue , then press A button to begin writing nand.

It will take a moment to write the nand, once nand is done.

Press any button to continue, then BACK button = Return to main menu

then Back Button once more, to SHUT DOWN. Will countdown, then turn off.

Step 4 - Updating dashlaunch

This is pretty self explanatory, need to download the new dashlaunch 3.21 folder, add to usb, plug usb into console delete the old, and paste the new.

If anyone needs help or has issues updating send me a PM.

S/o to c0z and others involved in making a speedy reliable xebuild and dashlaunch to go along with it. again.

Enjoy the new dash

https://gyazo.com/c6c7221e8d77af6dc6e5bcaac6c41766.png


Last edited by Streamah ; edited 5 times in total

The following 21 users thanked Streamah for this useful post:

Ambien (12-28-2019), TTG (11-14-2019), bradysa1234 (11-14-2019), Rodent (09-04-2019), IQ (08-24-2019), Tele (06-23-2018), Yamborghini (06-21-2018), Moonshine (05-26-2018), PinkRibbon (05-23-2018), Evox (05-23-2018), OneThousand (05-23-2018), DyI (05-23-2018), Chat (05-23-2018), XeCookie (05-23-2018), whosandy (05-23-2018), Ilusionz (05-23-2018), Johnny (05-23-2018), Rauben (05-23-2018), MrMw209 (05-23-2018), Exadious (05-23-2018), G6 (05-23-2018)
#2. Posted:
Exadious
  • Fairy Master
Status: Offline
Joined: Dec 23, 201310Year Member
Posts: 857
Reputation Power: 2493
Status: Offline
Joined: Dec 23, 201310Year Member
Posts: 857
Reputation Power: 2493
Awesome!

Thanks for this tutorial, I think that helps Modders which are not so experienced!

Easy to understand and easy to do :p

#3. Posted:
Tele
  • 2 Million
Status: Offline
Joined: Jan 30, 201410Year Member
Posts: 1,947
Reputation Power: 324
Status: Offline
Joined: Jan 30, 201410Year Member
Posts: 1,947
Reputation Power: 324
You forgot to mention about unplugging the console at the end of the tut, wouldn't like to see someone bricking their rgh.
#4. Posted:
Streamah
  • Summer 2020
Status: Offline
Joined: May 24, 201013Year Member
Posts: 10,103
Reputation Power: 3697
Status: Offline
Joined: May 24, 201013Year Member
Posts: 10,103
Reputation Power: 3697
Tele wrote You forgot to mention about unplugging the console at the end of the tut, wouldn't like to see someone bricking their rgh.


when you shut down through flash 360 it does a cold shut down. basically the same as unplugging the powerbrick. ive personally just tested that after updating my console. i did not unplug , waited a few seconds after it shut down and rebooted and it was fine.

sometimes in some cases though yes unplugging the powerbrick after you reflash your nand will ensure it gets flashed successfully
#5. Posted:
Boulton
  • Trusted Seller
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
Will try this in a second, thanks dude
#6. Posted:
Status: Offline
Joined: Jan 06, 20186Year Member
Posts: 221
Reputation Power: 23
Status: Offline
Joined: Jan 06, 20186Year Member
Posts: 221
Reputation Power: 23
Ill do this tonight, Thanks for the tutorial man.
#7. Posted:
Chat
  • Winter 2020
Status: Offline
Joined: Jan 10, 201212Year Member
Posts: 7,910
Reputation Power: 7437
Status: Offline
Joined: Jan 10, 201212Year Member
Posts: 7,910
Reputation Power: 7437
Great Guide, Thank you for the share hopefully people don't brick their consoles now

I wanted to add, I did this and although a USB probably is better, I personally did everything though Xbox 360 Neighborhood


Last edited by Chat ; edited 1 time in total
#8. Posted:
Boulton
  • Trusted Seller
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
I put the flash360 on my USB for the first step, go into xex menu and then start the flash.xex and it comes up with

SFC_init Failure:0x00000003
Config Register: 0x000430c4

Press any button to exit application

Anyone know what's going on?
#9. Posted:
Saxbyy
  • TTG Addict
Status: Offline
Joined: May 10, 20185Year Member
Posts: 2,707
Reputation Power: 578
Status: Offline
Joined: May 10, 20185Year Member
Posts: 2,707
Reputation Power: 578
BoultonsMods wrote I put the flash360 on my USB for the first step, go into xex menu and then start the flash.xex and it comes up with

SFC_init Failure:0x00000003
Config Register: 0x000430c4

Press any button to exit application

Anyone know what's going on?


Is it a corona?

If so use this: homebrew-connection.org/simple-36...ort-added/
#10. Posted:
Boulton
  • Trusted Seller
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
Status: Offline
Joined: Mar 07, 20159Year Member
Posts: 3,550
Reputation Power: 2534
Yeh, sweet cheers man
Users browsing this topic: None
Jump to:


RECENT POSTS

HOT TOPICS